Leaderboard


Popular Content

Showing most liked content since 05/29/2017 in Posts

  1. 1 like
    Bad timing - Dr G, Shay (Marketing Director), and I were all on vacation and we had a technical glitch (or maybe we got hacked and someone wanted ransom?). It's all good now.
  2. 1 like
    When I first used it I was like it is so so. But after extended use I have to say it has become my favorite interior protectant. Leaves a great finish and as you stated very durable. Also does not attract much dust compared to other products. I just bought more.
  3. 1 like
    Best explanation available: Yvan Lacroix The new line is designed as a maintenance line for coated cars. These are not simply re-bottled Optimum products, but new formulations that Dr G. has worked on for quite some time to compliment coated cars. Fortunately for the rest of the world they work great on non coated cars as well. They will only be available through the www.opticoat.com website, or directly from Opti-Coat Pro installers. Retailers will not have access to this line of products. We do not have the products in stock in the USA, a preliminary batch was made to ship to our distribution partners world wide, so they could all be launched at once. In the USA we do not have product yet, and the website is going through a redesign to accommodate these new products. Until the website is ready they will not be available here. I can not give you a date at this time.
  4. 1 like
    This is an update on how the coating fared. It's been 17 months since I have seen this car. I had my uncle bring it by to do a decon wash to evaluate how gloss coat has been doing. I started off with the wheels and tires and then proceeded to spray Ferrex onto the painted surface. I let that sit for a few minutes. I rinsed it off and saw some unexpected behavior. So I proceeded with a wash. I used CarPro Reset to wash it. As I was done washing this is what I saw. Similar behavior as when I rinsed the surface free of ferrex. No beading or sheeting. Water was laying flat. Primarily on the flat surfaces. The sides were barely clinging on. Rear Quarter Hood Trunk Roof The only area that showed signs of life was the front bumper I dried the car off and then moved it into the garage thinking maybe it just had some built up road grime. On an episode of the optimum synergy podcast dated on 2/21/2017 there is a discussion on how to do a decon wash using Optimum MDR at 3:1 and Power Clean at 3:1 and agitate each step with a dampened towel in ONR. I won't go into too much detail on the steps. After this is done it is recommended to rinse the surface with water. I even did the so called wash, clay, wax method using optimum car wax and a fine grade clay towel on one area of the hood. I did the baggie test and there was not very much contaminants on the paint. I said lets give it another wash with Reset. Well same behavior. Gloss Coat has indeed failed on the above shown surfaces. It was barely clinging onto the sides. The front bumper was the only area that had any signs of life. Now this is the newest formula of Gloss Coat which is stated to last 3 years (36 months). Optimum guarantees it for 2 years (24 months). This is quite a disappointment that it did not even make it to 2 years before it failed. I asked my uncle was this taken to a tunnel wash or coin op wash. He said no and that he washes all the cars at home with Meguiar's Deep Crystal car shampoo. The weather here in Southern California has been dry for the most part. Other than December 2016 into around February/March 2017 time frame where it did rain more than usual. It is possible that Gloss Coat did not bond well as CarPro Eraser was used since Optimum Paint Prep was not out at the time. Anyway I could not let it leave with lack luster protection. I cleaned up the interior and protected it with GTechniq C6 Matte Dash Cleaned all the glass with McKee's 37 20/20. The back window had some nasty crud on it and turned my applicator brown. 20/20 is good stuff. Treated the trim Polished up the stainless steel tips Meghan of Autogeek sent me this tire gel to review. I went ahead and used it to get my thoughts ready for a review on the Autogeek forum. 1 coat in full sun on the rear tire. I did not buff it. It dried to the touch in about 20 mins. 1 coat on the front tire in full sun For protection I went ahead and just used opti-seal for the fact it is quick to use. I let it sit for an hour before I wiped it down with optimum instant gloss detailer. Recap, Gloss Coat has failed at the 17 month mark which is a little disappointing given that optimum guarantees it to last 2 years. Doesn't really give me confidence on how it will hold up on my dad's car that also has gloss coat. I hope it lasts longer than this. I told my uncle if he wants me to polish it later on I will do so. The paint is swirled out. My cousin is the owner of it so he has been taking over the maintenance of it in terms of washing the car at home. I came to the conclusion of not re-coating this car. If I ever work on it again it will either be a one step cleaner wax type product or a one step polish and seal. This will be the last update to this thread with regards to gloss coat.
  5. 1 like
    Optimum Gloss-Coat™ is the most advanced polymer system that forms a layer of clear coat over automotive finishes. Optimum Gloss-Coat™ provides better scratch and mar resistance, better UV resistance, better chemical etch resistance, and has better release properties than any other consumer product while providing unsurpassed gloss and slickness. Additionally, you can top Optimum Gloss-Coat™ with any non-abrasive wax or sealant of your choice to add additional gloss and slickenss. Optimum Gloss-Coat™ can be used to protect the following surfaces: • painted surfaces • wheels • plastic trim • bumpers • aluminum & chrome surfaces Since Optimum Gloss-Coat™ bonds to surfaces it is applied to, any paint imperfections must be removed with Optimum Polish II or Optimum Hyper Polish before application. Also all waxes and oils must be removed from the surfaces for proper bonding. Directions: 1. Polish paint with Optimum Polish II or Optimum Hyper Polish to remove any defects. 2. Clean surface with 15% IPA solution to remove all polishing oils, waxes, and silicones. 3. Prime the applicator by making an X pattern across the pad. Only a few drops will be needed for each subsequent panel. 4. Wipe Optimum Gloss-Coat™ onto a single panel at a time in a thin layer using two directions, in a circular or front to back direction. 5. Within 5 minutes, inspect the panel with adequate lighting looking for any thick areas that have not flashed away to clear. 6. Use foam applicator or paint safe microfiber to even out any areas where you see streaks. This step is key, as any spots not leveled will have to be polished if allowed to cure. Panels will feel a bit tacky and will be self-leveling during cure time, so avoid any unnecessary touching, wiping, or contact to produce the best results. 7. Repeat steps 1-6 for each panel where application is desired. Not recommended for glass.